top of page

Radiator Recycling: How to Separate Copper and Aluminum from Scrap Radiators

9 hours ago
4 min read
radiator recycling

Short answer: Radiator recycling recovers copper and aluminum from scrap radiators. After any remaining coolant or refrigerant is drained, the radiators are shredded, milled to free the copper tubes from the aluminum fins, and then separated by density. Copper is more than three times heavier than aluminum, so a densimetric separator can split them cleanly. A magnet removes steel parts. The result is clean copper and clean aluminum, which sell for much more than whole radiators.

Key Takeaways

  • Most scrap radiators are a mix of copper, aluminum, brass, steel and plastic.

  • Selling clean copper and aluminum separately earns much more than selling mixed radiators.

  • Typical process: pre-treatment → shredding → magnetic separation → milling → density separation.

  • Magnets remove only steel. Copper and aluminum are separated by density.

  • Coolant, oil and refrigerant must be removed before mechanical processing.

What Are Radiators Made Of?

Radiator Type

Main Materials

Common Sources

Copper-aluminum (Cu/Al, ACR)

Copper tubes + aluminum fins

Air conditioners, refrigeration units, heat pumps

Aluminum car radiators

Aluminum core + plastic tanks

Modern cars and trucks

Copper-brass radiators

Copper fins + brass tubes and tanks

Older vehicles, trucks, industrial equipment

Mixed radiators and heat exchangers

Cu, Al, brass, steel brackets

Industrial cooling, HVAC systems

Copper-aluminum radiators are among the most common and valuable radiator scrap. They’re known in the scrap trade as ACR (aluminum copper radiators).

Why Separate Copper and Aluminum from Radiators?

Scrap buyers usually pay a lower price for whole radiators because the metals are still attached to each other and to steel and plastic parts. When a recycler separates them in-house:

  • Copper is sold at a much higher price as clean copper granules.

  • Aluminum is sold as clean aluminum.

  • Steel is recovered separately.

That’s why radiator recycling machines can pay off quickly for scrap yards and HVAC recyclers that handle radiators regularly.

How Does Radiator Recycling Work? Step by Step

1. Pre-treatment

Any remaining coolant, oil or refrigerant is drained and handled according to local regulations. Large steel frames and loose plastic parts can be removed at this stage.

2. Shredding: double shaft shredder

A double shaft shredder tears radiators into smaller pieces and opens up the copper tubes and aluminum fins.

3. Ferrous removal: magnetic separator

A magnetic separator removes steel brackets, screws and frames from the shredded material.

4. Liberation: hammer mill

A hammer mill breaks the shredded pieces further by impact and frees the copper tubes from the aluminum fins.

5. Fine milling: turbo mill

A turbo mill reduces the material to small, uniform particles, ready for precise separation.

6. Separation: densimetric separator

A densimetric separator splits copper and aluminum using their large difference in density. Copper is about 8.96 g/cm³, aluminum about 2.70 g/cm³.

7. Dust collection

A dust collector extracts fine dust throughout the process, which keeps separation clean and the work area safe.

Common Mistake: Magnets Don’t Separate Copper or Aluminum

Copper and aluminum are not magnetic. A magnetic separator removes only steel and iron. Copper and aluminum are separated from each other by density (densimetric separator), and from non-metals by density or eddy current separation.

MİZAR Solutions for Radiator Recycling

MİZAR Recycling Machinery manufactures radiator recycling lines in Konya, Türkiye.

MMP Series (Multi Metal Plant) for radiators, PCBs, e-waste and other mixed metal-bearing waste:

  • DSH double shaft shredder

  • OMS F ferrite magnetic separator

  • HMR hammer mill with Hardox® 500 hammers

  • TRM turbo mill

  • DES densimetric separator with DTF A dust collector

  • PLC-controlled, available as MMP S / M / L with capacities of up to 400 / 800 / 1,300 kg/h

Combined lines: MİZAR also designs custom lines that process radiators, cables and PCBs on one plant, sharing a common separation section. In 2025, MİZAR installed a combined line in Finland that processes cable, PCBs, radiators and other solid waste.

Frequently Asked Questions

How do you separate copper from aluminum in radiators?

The radiators are shredded and milled to free the copper tubes from the aluminum fins. A densimetric separator then splits the two metals by their difference in density.

What is an ACR radiator?

ACR stands for aluminum-copper radiator, the type with copper tubes and aluminum fins found in air conditioners and refrigeration units.

Can a magnetic separator separate copper and aluminum?

No. Neither metal is magnetic. Magnets remove only steel. Copper and aluminum are separated by density.

Do radiators need to be drained before recycling?

Yes. Coolant, oil and refrigerant must be removed and handled according to local regulations before mechanical processing.

Can the same line process radiators and PCBs?

Yes. MİZAR’s MMP lines are designed for radiators, PCBs, e-waste and other mixed metal-bearing scrap.

Conclusion

Radiators are a common scrap stream with real copper and aluminum value, but that value is only captured when the metals are separated cleanly. With shredding, milling and density separation, MİZAR’s radiator recycling lines turn mixed radiators into high-value copper and aluminum.

Processing radiators? Contact MİZAR for a line configuration based on your radiator mix and volume.

📞 +90 537 520 35 34

 
 
bottom of page