Flex Cable Recycling: How to Recover Copper from Flexible Cables

Short answer: Flex cables can’t be stripped efficiently by hand or with standard stripping machines, because they’re soft and full of very fine copper strands. The practical way to recycle them is granulation: the cable is shredded and cut into small particles, then copper and plastic are separated by air or density separation. A well-configured granulation line gets clean, high-purity copper out of flexible cable scrap that would otherwise be sold at a low price as mixed cable.
Key Takeaways
Flex cable is a highly bendable cable made of many fine copper strands inside PVC or rubber insulation.
Its softness and fine strands make manual or mechanical stripping slow and uneconomical.
Granulation followed by air/density separation is the standard industrial method for recycling it.
The main technical challenge is fine copper: without the right separator, thin copper strands get lost in the plastic fraction.
Lines with a zigzag air classifier and turbo mill recover far more fine copper than basic granulator + separator setups.
What Is a Flex Cable?
A flex cable (flexible cable) is an electrical cable built to bend over and over without breaking. Instead of one solid or a few thick copper wires, each conductor is made of many very thin copper strands (Class 5 or Class 6 conductors). These are wrapped in insulation, an outer sheath and sometimes a shielding layer. The insulation and sheath are usually PVC or rubber.
Where flex cables are used:
Household appliances such as vacuum cleaners and kitchen devices
Portable power tools and extension cords
Industrial machines with moving parts, like conveyors and robotic arms
Any installation that needs a cable to move or bend often
Because they’re in almost every appliance and machine, flex cables make up a large and steady share of the low-grade cable scrap at recycling yards.
Why Is Flex Cable Hard to Recycle?
The same properties that make flex cable useful make it hard to recycle:
It’s too soft to strip. Cable strippers need a firm cable to cut the insulation cleanly. Flex cable bends and twists away from the blade.
The strands are too fine. Thin copper strands tangle and break, so separating them from the insulation by hand is extremely slow.
It has several layers. Insulation, sheath and sometimes shielding all have to be removed.
It’s often short and mixed. Appliance cords come in short pieces with plugs attached, so feeding them into a stripper one by one isn’t practical.
As a result, manual stripping of flex cable is rarely worth the labor cost. Many yards end up selling it as low-value mixed cable.
Manual Stripping vs. Granulation for Flex Cable
Criteria | Manual / Mechanical Stripping | Granulation Line |
Suitable for flex cable | Poor, cable is too soft | Yes, designed for it |
Handles short/mixed pieces | No | Yes |
Labor needed | High, piece by piece | Low, continuous feeding |
Throughput | Low | High (kg/h, scalable) |
Output | Copper wire + insulation | Copper granules + plastic granules |
Fine copper recovery | Low | High with proper separation |
How Does Flex Cable Granulation Work?
A typical flex cable recycling process has four stages:
Pre-shredding: A single-shaft or double-shaft shredder cuts the cable into smaller pieces. This step also handles plugs and long tangled bundles.
Granulation: A granulator with sharp, precisely set blades cuts the pieces into small particles (usually 3–5 mm), freeing the copper from the insulation.
Separation: An air classifier or densimetric (density) separator splits the particles into a copper fraction and a plastic fraction, using the difference in weight between copper and PVC/rubber.
Fine copper recovery: A turbo mill and zigzag separator re-process the plastic fraction to capture the fine copper strands a single separation step would miss. Dust is extracted throughout.
Why step 4 matters for flex cable: Thin copper strands are light. In a basic separator they can blow over into the plastic fraction, which lowers your copper yield. For flex cable, a fine-copper recovery stage is often what decides whether the line is profitable.
MİZAR Recycling Solutions for Flex Cables
MİZAR Recycling Machinery designs and manufactures cable granulation lines in Konya, Türkiye, configured for the cable mix each customer actually processes.
PRP M Line: a high-performance cable granulation line for mixed and fine cables. A zigzag separator splits thick copper, fine copper and plastic, and a turbo mill re-processes the material. It’s well suited to flex-heavy cable streams.
EPR M-Line: a pre-shredder + granulator + separation configuration for general cable recycling.
CMT Compact Series: a compact line for smaller volumes (granulator → turbo mill → densimetric separator + dust collector), with copper purity of up to 99.9%.
CRP (Copper Recovery Plant): recovers the copper left in plastic fractions from an existing granulation line.
What our engineering focuses on:
High copper recovery with minimal fine-copper loss
Re-sharpenable, durable blades and rotors for soft, flexible cable types
Energy-efficient configurations sized to your capacity
Components from European, US, Japanese or Turkish brands, depending on your budget
Frequently Asked Questions
Can flex cable be stripped with a cable stripping machine?
Generally, no. Flex cable is too soft and its strands are too fine for clean stripping. Granulation is the recommended method.
What copper purity can you get from flex cable granulation?
With a properly configured granulation and density separation line, copper purity of up to 99.9% is achievable. Actual results depend on the cable mix and the separation equipment used.
Why is fine copper lost when recycling flex cable?
Fine copper strands are light and can be carried into the plastic fraction during air separation. Adding a turbo mill and zigzag air classifier captures this fine copper.
What is the difference between rubber and PVC flex cable in recycling?
Both can be granulated. Rubber-insulated cables are tougher on blades and may need different screen sizes and blade settings, so tell your machine supplier about your cable mix.
Which MİZAR machine is best for flex cable?
For flex-heavy or mixed fine cable, the PRP M Line is the strongest option. For smaller volumes, the CMT Compact Series is a cost-effective starting point.
Conclusion
Flex cables are everywhere, from household appliances to industrial machines, but their soft structure and fine copper strands make manual stripping impractical. Granulation with proper fine-copper separation is the efficient, scalable way to turn flex cable scrap into high-value copper.
Planning to process flex cable?
Contact MİZAR for a line configuration based on your cable mix and capacity.
📞 +90 537 520 3534


